|
|
Prev. Next
The list below shows items 1001 to 1200 of 32208
total items:
Prev. Next
Top of Page
|
|
Diagnosing Electrical Problems
Typically, you discover you have an electrical problem when you turn
on a lamp or appliance and it won't work. When that happens, the source
of the problem may be the device itself, faulty wiring connections, an
overloaded or a short circuit.
Overloaded circuit
A circuit becomes overloaded when there are more lamps and appliances
on it than it can safely handle. When all the lamps and appliances are
turned on, the wiring overheats and the fuse blows or the circuit breaker
trips. Top of Page
Short circuit
A short circuit occurs when a bare hot wire touches a bare neutral wire
or a bare grounded wire (or some other ground). The flow of extra current
blows a fuse or trips a circuit breaker.
Helpful Diagnostic Hint
Plug fuses provide a clue to what made them blow. Like:
- An overload melts the bridge.
- A short circuit blackens the glass.
Top of Page
Troubleshooting Electrical Problems
Light Fixture Won't
Work
Check for:
- Burnt out bulb or fluorescent tube.
- Defective fluorescent starter.
- Faulty switch.
- Loose wiring.
- Faulty socket.
Remedies:
- Replace bulb or tube.
- Replace fluorescent starter.
- Replace switch.
- Tighten connections at switch or fixture.
- WHAT ABOUT SOCKET?
Top of Page
Appliance Won't
Work
Check for:
- Overloaded circuit.
- Damaged plug.
- Damaged cord.
- Loose wiring.
- Defect in appliance or lamp.
Remedies:
- Test for overload -- shift appliance or lamp to another circuit.
- Replace plug.
- Replace cord.
- Tighten connections at switch or receptacle.
- Test in another circuit -- repair if faulty.
Top of Page
Appliance or
Lamp Won't Work in One Circuit -- Works in Others
Check for:
- erloaded circuit.
- Loose connection at receptacle.
- Short circuit.
Remedies:
- Test for overload; shift appliance or lamp to another circuit.
- Tighten connections at receptacle.
- Test for short circuit; make necessary repair.
Top of Page
Appliance or Lamp
Won't Work in One Receptacle of Circuit
Check for:
- Loose wiring.
- Faulty receptacle.
- Short circuit.
Remedies:
- Tighten connections at receptacle.
- Replace receptacle.
- Test for short circuit; make necessary repair.
Top of Page
Appliance or Lamp
Won't Work in Switch-Controlled Receptacle
Check for:
- Loose wiring.
- Faulty switch.
- Faulty receptacle.
Remedies:
- Tighten connections at switch or receptacle.
- Replace switch.
- Replace receptacle.
Top of Page
Some Lights on
Circuit Won't Work
Check for:
- Loose wiring.
- Faulty switch.
Remedies:
- Tighten connections at switch or fixture.
- Replace switch.
Top of Page
No Lights on Circuit
Work
Check for:
- Overloaded circuit.
- Short circuit.
- Loose wiring.
- Faulty switch.
Remedies:
- Test for overload; make necessary adjustment.
- Test for short circuit; make necessary repair.
- Tighten connections at switch.
- Replace switch.
Top of Page
Tracing a Short
Circuit or Overload
A blown fuse or tripped circuit breaker is a signal that you may have
either a short circuit or an overload in the electrical system.
- Look for black smudge marks on switch or receptacle cover plates,
or for frayed or damaged cords or damaged plugs on lamps and appliances
connected to the dead circuit.
- Replace a damaged cord or plug.
- Then replace the fuse or reset the breaker.
- If the circuit goes dead after an appliance has been in use for a
short time, you probably have an overloaded circuit.
- Move some of the lamps and appliances to another circuit and replace
the fuse or reset the circuit breaker for the first circuit.
Top of Page
Don't find any of
the above signs of trouble? Trace your way through the circuit using the
steps below.
- Turn off all wall switches and unplug every lamp and appliance on
the dead circuit.
- Install a new fuse or reset the tripped breaker.
- If the fuse blows or the breaker trips right away, the problem may
be a short circuit in a switch or receptacle.
- With the circuit dead, remove each cover plate and inspect the device
and its wiring.
- Look for charred wire insulation, wire shorted against the metal box
or a device that's defective.
- Replace a defective device.
- Call in an electrician to replace faulty wiring.
- If the new fuse doesn't blow or the breaker doesn't trip right away,
turn on each wall switch, one by one, checking each time to see if the
fuse has blown or the circuit breaker has tripped.
- If turning on a wall switch causes a fuse to blow or the breaker to
trip, there's a short circuit in a light fixture or receptacle, controlled
by that switch, or there's a short circuit in the switch wiring.
- With the circuit dead, inspect the fixture, receptacle, and switch
for charred wire insulation or faulty connections.
- Replace a faulty switch or fixture.
- Call in an electrician to replace wiring.
Top of Page
Problem still
not solved? You probably have faulty wiring. Call an electrician to correct
the problem.
If turning on a wall switch doesn't blow a fuse or trip the breaker,
the trouble is in the lamps or appliances.
- Test them by plugging them in one by one.
- If the circuit doesn't go dead, the circuit was overloaded.
- Move some of the lamps or appliances to another circuit.
- If the circuit does go dead just after you've plugged in a lamp or
appliance, then you've found the offender.
- If the circuit goes dead as soon as you plug in a lamp or appliance,
the plug or cord is probably at fault and should be replaced.
- If the circuit goes dead when you turn on the lamp or appliance, the
appliance or lamp or its switch is probably defective and should be
replaced or repaired.
Top of Page
Source: our affiliate partner: Acme Hardware
|